Sun-microsystems Sun Fire X4200 M2 Bedienungsanleitung

Sun Microsystems, Inc.www.sun.comSubmit comments about this document at: http://www.sun.com/hwdocs/feedbackSun Fire™X4100 and Sun Fire X4200Servers In

2 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 20065. Configure the preinstalled Solaris™ operating system or install a supportedope

Chapter 1 Setting Up the Server Hardware 3Disassembling the Slide-Rails Before InstallationUse this procedure to remove the mounting brackets from the

4 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Installing the Mounting Brackets Onto the ServerUse this procedure to install the

Chapter 1 Setting Up the Server Hardware 5Attaching the Slide-Rail Assemblies to the RackUse this procedure to install the slide-rail assemblies to th

6 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Installing the Server Into the Slide-RailAssembliesUse this procedure to install

Chapter 1 Setting Up the Server Hardware 74. Simultaneously pull and hold the slide-rail release buttons on each mountingbracket while you push the se

8 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 20064. Verify that the CMA rail extension engages the slide-rail, as shown in FIGURE

Chapter 1 Setting Up the Server Hardware 9FIGURE 1-7 Inserting the CMA Mounting Bracket Into the Rear of the Right Slide-Rail6. Insert the right CMA s

10 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 20067. Insert the remaining CMA arm connector into the plastic cutout on the CMA rai

Chapter 1 Setting Up the Server Hardware 11FIGURE 1-10 Installing CMA Cable HangersAttaching and Routing CablesUse this procedure to attach cables to

Copyright 2005 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved.Sun Microsystems, Inc. has intel

12 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Verifying Operation of the Slide-Rails and CMAUse this procedure to ensure that

Chapter 1 Setting Up the Server Hardware 13CablingAttach cables to the back panel connectors of your server as required. See FIGURE 1-11or FIGURE 1-12

14 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 20064. Connect Ethernet cables to the “NET” connectors as required for your GigabitE

Chapter 1 Setting Up the Server Hardware 15Powering On and Powering Off theServerYou have to apply only standby power to the server at this point so t

16 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Powering On Main Power Mode● To power on main power for all server components:a.

Chapter 1 Setting Up the Server Hardware 17 Emergency shutdown: Press and hold the Power button for four seconds to forcemain power off and enter sta

18 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006

19CHAPTER2Setting Up the Server SoftwareThis chapter describes the tasks for initial setup of the server’s service processor andIntegrated Lights Out

20 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006ILOM consists of four components, three of which are on your host server and one

Chapter 2 Setting Up the Server Software 21Connecting to the ILOM ServiceProcessorThere are two methods for connecting to the ILOM SP to perform initi

iiiContentsPreface v1. Setting Up the Server Hardware 1Installation Overview 1Installing the Server Into a Rack With Optional Slide-Rails 2Disassembli

22 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 20064. Press Enter on the terminal device to establish a connection between that ter

Chapter 2 Setting Up the Server Software 23Connecting to ILOM Using an EthernetConnectionTo access the full range of ILOM functionality such as the gr

24 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006a. Identify the MAC address of the ILOM SP from one of the following locationsan

Chapter 2 Setting Up the Server Software 25FIGURE 2-2 Opening a Session With an SSH Command-Line Interface To establish a connection to the ILOM SP w

26 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Configuring ILOM Using Static Ethernet SettingsAs an alternative to having your

Chapter 2 Setting Up the Server Software 27FIGURE 2-4 Integrated Lights Out Manager Network Settings PageConfiguring Static IP Addresses Using the CLI

28 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Configuring Static IP Addresses Using the BIOS Setup Utility1. Enter the BIOS Se

Chapter 2 Setting Up the Server Software 29Setting Up Platform Operating Systemand Driver SoftwareAfter configuring the ILOM SP with network settings,

30 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006

31CHAPTER3Configuring the Pre-installedSolaris 10 Operating SystemThis chapter explains the steps for configuring the Solaris™10 Operating System(OS)

iv Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Connecting to the ILOM Service Processor 21Connecting to ILOM Using a Serial Con

32 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006TABLE 1 Worksheet for InstallationInformation for Installation Description or Ex

Chapter 3 Configuring the Pre-installed Solaris 10 Operating System 33Name service:if the systemuses a nameservice, providethe followinginformation.Na

34 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Default route Do you want to specify a default route IP addressor let the Solari

Chapter 3 Configuring the Pre-installed Solaris 10 Operating System 35Configuring the Pre-Installed Solaris 10Operating SystemNote – Before you perfor

36 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006▼ To Connect to the Server Using the ServiceProcessor’s IP AddressNote – This pr

Chapter 3 Configuring the Pre-installed Solaris 10 Operating System 37The screens that are displayed will vary, depending on the method that you chose

38 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006▼ To Connect to the Server Using a Serial CaptureProgram1. Use a cable to connec

Chapter 3 Configuring the Pre-installed Solaris 10 Operating System 39Solaris 10 User DocumentationYou can access the various collections of the Solar

40 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006

41IndexBback panel cable connectors 13back panel illustration 13Ccable management assembly 7cables 13client-side secure shell 20CMA assembly 7connecto

vPrefaceThis Sun Fire X4100 and Sun Fire X4200 Installation Guide contains procedures forinstalling the server in a rack, cabling, and powering on the

42 Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006configuring with Ethernet 23configuring with serial 21firmware 20hardware 20shuttin

vi Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006Product UpdatesFor product updates that you can download for the Sun Fire X4100

Preface viiTypographic ConventionsSun Welcomes Your CommentsSun is interested in improving its documentation and welcomes your comments andsuggestions

viii Sun Fire X4100 and Sun Fire X4200 Installation Guide • October 2006

1CHAPTER1Setting Up the Server HardwareThis chapter contains the following topics: “Installation Overview” on page 1 “Installing the Server Into a R