Sun-microsystems Netra 120 Bedienungsanleitung Seite 173
- Seite / 200
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 11 Replacing a Server or Replacing Individual Components 11-19
11.8 Replacing the Rear Fan Subassembly
(Fans 1 and 2)
Caution – The procedure below is for the attention of qualified service engineers
only. Before touching or replacing any components inside the server, disconnect all
cables and follow the instructions in Section 4.2, “Opening the Server” on page 4-4
which tell you how to open the server. Always place the server on a grounded ESD
pad and wear a properly grounded antistatic wrist strap.
1. Open the server by following the instructions in Section 4.2, “Opening the
Server” on page 4-4.
Make sure you disconnect all external cables and pay particular attention to the
information about how to prevent electro-static discharge from your body from
damaging the components of the server.
2. With the server open and seated on top of an ESD pad, and with a properly
grounded antistatic wrist strap on your wrist, disconnect the old subassembly’s
power cables from the system board (see
FIGURE 11-10).
3. Lift out the old subassembly and discard it.
4. Insert the new fan subassembly into its bay in the chassis.
5. Connect the fan cables to the system board (see
FIGURE 11-10).
6. Replace the server’s cover and tighten the captive screw (see
FIGURE 4-9 in
Section 4.7, “Replacing the Server’s Top Cover” on page 4-14).
- Sun Fire 1
- V120 and Netra 1
- Server User’s Guide 1
- Contents 3
- Contents v 5
- Contents vii 7
- Contents ix 9
- Figures xiii 13
- How This Book Is Organized 17
- Using Solaris Commands 18
- Typographic Conventions 19
- Shell Prompts 19
- Related Documentation 20
- Sun Welcomes Your Comments 20
- Safety Precautions 21
- Introduction 25
- 120 Servers 26
- 1.2 Contents of the Ship Kit 27
- Contents of the Ship Kit 28
- Chapter 1 Introduction 1-5 29
- 1.4 Front Panel 30
- 1.5 Back Panel 31
- Netra 120 Servers 32
- Chapter 1 Introduction 1-9 33
- What’s Next? 34
- Power and Cooling 35
- 2.2 Power Consumption 37
- Using DC Power 39
- M5 grounding 40
- Chapter 3 Using DC Power 3-3 41
- 0.31 in. (8 mm) 42
- Chapter 3 Using DC Power 3-5 43
- FIGURE 3-3). This opens the 43
- FIGURE 3-4) 43
- FIGURE 3-3 and FIGURE 3-4) 44
- Chapter 3 Using DC Power 3-7 45
- FIGURE 3-6) 45
- FIGURE 3-7) 45
- FIGURE 3-8) 46
- FIGURE 3-9) 46
- Installing Optional Hardware 49
- Components 49
- SCSI Hard Disk Drives 50
- 4.2 Opening the Server 52
- Removing the Top Cover 53
- FIGURE 4-4: 54
- CD-ROM Drive 55
- Paddleboard 56
- 4.6.1 Installing a PCI Card 59
- PCI connector 60
- Plastic bracket 61
- 4.6.2 Removing a PCI Card 62
- Cable Management Bracket 66
- 19-inch Rackmounting Kit 66
- FIGURE 5-2) 67
- FIGURE 5-3) 67
- FIGURE 5-7) 71
- FIGURE 5-8) 73
- Inch Rack 74
- Cable management bracket 74
- Fixed Mounting Bracket Kit 76
- FIGURE 5-11) 77
- FIGURE 5-11, but do not fit 77
- FIGURE 5-12) 77
- Connecting the Cables 79
- ■ Single Ended (SE) 81
- ■ Narrow (8-bit) 81
- ■ Wide (16-bit) 81
- ■ Dumb terminal 82
- ■ Sun workstation 82
- FIGURE 6-3) 83
- TABLE 6-1. Then make 83
- TABLE 6-2 85
- TABLE 6-3 86
- Rate 9600 baud 87
- Parity No 87
- Stop bits 1 87
- Data bits 8 87
- Netra 120 Server 91
- 7.1.1 Using a Terminal Server 92
- 7.2 Powering On the Server 93
- # sys-unconfig 96
- LOM device 102
- From the LOM Shell 103
- 8.2.4 Resetting the Server 105
- 8.2.6.1 Boot Modes Available 107
- Before It 112
- ■ Reset permission (r-level) 113
- ■ Alphabetic 114
- ■ Numeric 114
- ■ Period (.) 114
- ■ Underscore (_) 114
- ■ Hyphen (-) 114
- Variables 117
- Serial A/LOM port 118
- # eeprom input-device=ttyb 119
- # eeprom output-device=ttyb 119
- # reboot 119
- LOM Sends to syslogd 120
- LOM Commands 121
- LOM Commands (Continued) 122
- Managing the Server From the 125
- Solaris Prompt 125
- # man lom 126
- # lom -p 126
- Circuit Breakers (lom -v) 127
- (lom -l) 129
- Configuration (lom -w) 129
- (lom -c) 130
- ● To see the event log, type: 131
- System After a Lockup 132
- # lom -W on,40000,10000 133
- # lom -W on,40000,10000 -R on 133
- Script or Command (lom -R on) 134
- From Solaris 135
- # lom -F off 136
- # lom -X x 136
- # lom -E off 136
- (lom -B) 137
- (lom -G filename) 137
- Troubleshooting 141
- SunVTS Diagnostic Tools 142
- 10.1.3 Using SunVTS 145
- 10.1.3.2 Installing SunVTS 146
- # cd /opt/SUNWvts/bin 147
- FIGURE 10-3 shows 148
- Encounter 150
- Sequence 151
- FIGURE 10-7) 152
- Link 0 Link1 Fault Power 153
- Individual Components 155
- 11.1 Replacing a Server 156
- Tie-wrap hole 157
- 11.2 Field Replaceable Units 158
- FIGURE 11-2) 159
- Cable, and Paddleboard 161
- FIGURE 11-3) 162
- FIGURE 4-9 in 162
- 11.5 Replacing the NVRAM Chip 163
- FIGURE 11-5) 164
- Replacing the NVRAM Chip 165
- FIGURE 11-7 The System Board 168
- FIGURE 11-7) 169
- FIGURE 11-7). Do not put any 169
- Replacing the Fan 3 Assembly 170
- FIGURE 11-9) 171
- (Fans 1 and 2) 173
- 11.9 Replacing Fan 3 175
- IV Appendixes 177
- Hard Disk Drive with Solaris 179
- Solaris Running 180
- Operating 185
- Environment 185
- B.1 Reinstalling Solaris 186
- Software 186
- APPENDIX 187
- C.1 The LOM Device Driver 188
- TABLE C-1 189
- Field Format Default Effect 190
- System Board Jumper Settings 193
Verwandte Produkte und Handbücher für Computers Sun-microsystems Netra 120
(184 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.182 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern